Simple FM Receiver with Audio Amplifier
FM radio receiver remains one of the mostsatisfying circuits to build fromscratch. This project combines acompact front-end tuner using a BF256junction field-effecttransistor (JFET) with apowerful LM386 audio amplifier IC todeliver clean, audible FM receptionthrough an 8Ω speaker — allfrom a single 9V supply.
Whether you are anelectronics student buildingyour first RF project or aseasoned hobbyist lookingfor a weekend build, this circuit isstraightforward, uses widely availablecomponents, and can be assembled on ageneral-purpose PCB or breadboard.
This is adirect-conversionreceiver design, sometimes alsodescribed as a regenerative receiver.Unlike a superheterodyne radio, whichmixes the incoming signal down to afixed intermediate frequency of 10.7MHz before detection, this circuitprocesses the FM signal directly at thereceived frequency. This keeps thecomponent count low, eliminates theneed for ceramic IF filters, and makesthe circuit highly accessible forbeginners and hobbyists.
A direct-conversion receiver removes the mixer and IF stages entirely. The incoming RF signal is amplified, and detection happens directly at the carrier frequency. In regenerative designs, the active device — in this case the BF256 JFET — is biased close to oscillation, which dramatically increases its effective gain and selectivity. The detector and amplifier functions are performed by the same transistor simultaneously.
“Direct-conversion and regenerative receivers were the dominant radio architecture before the superheterodyne became standard in the 1930s. Today they remain popular in simple FM and shortwave designs because a well-built regenerative front end can rival a superheterodyne in sensitivity at a fraction of the component count.”
FM Receiver Circuit Overview
The circuit consists of three stages working in sequence:
- RF Tuner and Direct-Conversion Detector — antenna, LC tank circuit, and BF256 JFET operating as a self-oscillating detector
- Audio Recovery and Pre-Amplification — BC847 NPN transistor recovering and amplifying the detected audio signal
- Audio Power Amplification — LM386 IC driving an 8Ω speaker from a 9V supply
There is no mixer, no local oscillator separate from the signal path, and no IF filter at any fixed intermediate frequency. The VFP choke and HFC coil in the circuit are RF decoupling components, not IF filters.
RF Tuner and Direct-Conversion Detector
The antenna connects to an LC tank circuit formed by coil L and a variable capacitor network consisting of C, C*, C1, and C2. This resonant circuit selects the desired station from the FM band (88–108 MHz). The variable capacitor C (approximately 10 pF) allows manual tuning across the band.
The tuned signal feeds the Gate (G) of the BF256 N-channel JFET. The BF256 is well-suited to VHF operation, offering low noise and useful gain at FM frequencies. Resistor R2 (1 kΩ) at the drain and resistor R1 (10–22 kΩ) at the source establish the DC bias point. Capacitor C3 (6–100 nF) bypasses R1 for RF signals, maintaining AC gain without disturbing the DC operating point.
In this configuration, the BF256 is biased to operate as a self-oscillating mixer or regenerative detector. It simultaneously amplifies the incoming FM signal and detects the audio modulation riding on the carrier. The recovered audio appears at the drain of the JFET and is passed forward through the RF choke network to the BC847 stage.
“The BF256 JFET is well suited to this role because its high input impedance minimises loading on the LC tank circuit, preserving the resonant Q and therefore the selectivity of the tuner. A low-Q tank would make it impossible to separate adjacent FM stations.”
Coil L – Winding Specifications
Coil L is the most critical component in the receiver. It forms one half of the LC tank circuit that determines which station is received. The specifications from the circuit diagram are:
— 5 turns of enamelled copper (CuL) wire
— Wire diameter: 0.9 mm
— Winding diameter: 9 mm (wound on a 9 mm drill bit used as a mandrel)
— Winding length: approximately 4.5 mm for the close-wound section, with taps brought out at positions marked 1, 2, and 3
Wind the coil tightly on the drill bit, then slide it off carefully. No core or former is used. The air-core construction gives a stable, low-loss inductance at VHF that a ferrite-core inductor could not match at these frequencies.
“At FM frequencies above 88 MHz, ferrite cores introduce significant losses and detune unpredictably with temperature. Air-core coils wound from stiff enamelled copper wire are the correct choice for any VHF LC tank circuit.”
Audio Recovery and Pre-Amplification
The detected audio signal from the BF256 drain passes through a VFP choke (22 µH) and the capacitor network (C4, C6, C7) to the base of a BC847 NPN transistor. The VFP choke is an RF decoupling component — it blocks residual RF energy from passing beyond the detector stage into the audio circuitry. It is not an IF filter and does not operate at any fixed intermediate frequency.
The HFC coil shown in the circuit diagram is similarly a high-frequency decoupling choke. Its role is to prevent RF from coupling into the audio wiring and causing interference or instability. It does not perform any IF filtering or FM demodulation function.
The BC847 transistor amplifies the recovered audio signal to a level suitable for driving the LM386 input. Resistors R3 (680 kΩ) and R4 (3.3 kΩ) set the DC bias of the BC847. Capacitors C6 (470 nF) and C7 (470 nF) couple the signal while blocking DC between stages. The potentiometer P (60 kΩ, log taper) at the output of the BC847 stage serves as the volume control, feeding the audio signal into the LM386.
HFC Coil – Winding Specifications
— 16 turns of enamelled copper (CuL) wire
— Wire diameter: 0.6 mm
— Winding diameter: 3 mm
— Winding length: 9.6 mm
This coil acts purely as a high-frequency RF choke in the audio signal path. Wind it on a 3 mm mandrel and slide off carefully after winding.
LM386 Audio Power Amplifier
The volume-controlled audio signal from the potentiometer P feeds pin 3 (non-inverting input) of the LM386 via coupling capacitor C6 (10 nF). The LM386 is a low-voltage audio power amplifier IC designed specifically for battery-powered applications, and it is ideal here. The output drives an 8Ω speaker directly. The entire circuit is powered from a standard 9V battery.
Assembly and Testing Tips
- Wind the coils before anything else. Coil L and the HFC coil must be wound accurately before assembly begins. A deviation of even one turn in coil L will shift the tuning range significantly or prevent the circuit from reaching FM frequencies at all.
- Keep all RF wiring as short as possible. The antenna connection, coil L, and the BF256 Gate, Drain, and Source leads should be as short as physically practical. Long leads add stray inductance and capacitance that detune the tank circuit.
- Decouple the supply aggressively. Place 100 nF ceramic capacitors directly across the supply rails at the BF256 drain, at the BC847 collector, and at LM386 pin 6. Poor decoupling in a regenerative or direct-conversion design causes oscillation and instability far more readily than in a conventional superheterodyne.
- Turn the volume to minimum before first power-on. Set potentiometer P to its lowest position before applying the 9V supply for the first time.
- Tune very slowly. Because this is a direct-conversion design with no IF selectivity, the BF256 regeneration point is sensitive. Tune the variable capacitor C very slowly. Strong local FM stations will break through clearly as the tank circuit passes through resonance with each carrier frequency.
- Optimise R1 for your BF256 sample. JFETs of the same type number can have significantly different pinch-off voltages between individual devices. If sensitivity is poor, experiment with different values of R1 across the 10–22 kΩ range to find the best bias point for your specific transistor.
Circuit schematic sourced from http://www.qsl.net/va3iul/
Related Posts
- FM Bazooka Antenna for Superior FM Radio Reception (88–108 MHz)
- Slim-Jim Antenna for FM Broadcast Band reception (88–108 MHz)
- Build Your Own High-Res FM Receiver: The DIY CYD 480×320 FM Radio Project
- Faulkner FM Loop Antenna for Superior FM Reception
- Mini FM Radio Transmitter

Post Comment