Loading Now

40-10m OCF Antenna: A Simple, Multi-Band Wire Antenna

Are you looking for a single, efficient wire antenna that can cover multiple HF bands without the complexity of traps or the need for an external antenna tuner? The Off-Center Fed (OCF) dipole might be the perfect project for you. In this post, inspired by the classic design from OK1IKE.  we’ll explore building a compact 40-10 meter OCF antenna. It’s a great balance of performance, simplicity, and size.

Diagram of a 40-meter Off-Center-Fed (OCF) end-fed half-wave wire antenna showing a 16.9 m left arm and 4.1 m right arm connected through a 4:1 toroidal balun with approximately 16 turns. The feedpoint impedance is about 200 ohms, matched to a 50-ohm coaxial cable. Both wire ends terminate with dog-bone ceramic end insulators. The diagram also lists antenna specifications, including 1.5–2 mm copper wire diameter, 4:1 balun ratio, 50-ohm coaxial feedline, and approximate 200-ohm feedpoint impedance.

What is an OCF Dipole?

An Off-Center Fed (OCF) dipole is a half-wave wire antenna fed at a point not in the exact center . By carefully choosing the feed point, we can find an impedance that, when combined with a 4:1 balun, provides a good match to 50-ohm coaxial cable on several bands 

The secret to its multiband performance lies in the off-center feed point. While a standard dipole fed at its center has a low impedance (around 70 ohms) at its fundamental frequency, the OCF is fed at a point with a much higher impedance—around 200 to 300 ohms—which is close to optimal for multiband operation . The 4:1 balun transforms this down to a more manageable 50-75 ohms.

The 40-10m OCF Antenna Design

This specific antenna, which I’ll be building, is designed for the 40, 20, 15, and 10-meter bands. It’s based on a design from OK1IKE that uses a total wire length of approximately 21 meters, split into two unequal arms .

Antenna Specifications

  • Type: Off-Center Fed (OCF) Dipole
  • Target Bands: 40, 20, 15, and 10 meters
  • Total Length: ~21 meters 
  • Long Leg: 16.9 meters
  • Short Leg: 4.1 meters 
  • Feedpoint Impedance: ~200 ohms
  • Balun: 4:1 Ratio
  • Feedline: 50-ohm Coaxial Cable
  • Wire Diameter: 1.5-2 mm (approx. AWG 14-15)

Schematic diagram of a 4:1 current balun (Ruthroff-style transmission line transformer) used to match a 50-ohm coaxial feedline to a 200-ohm antenna. The transformer (Tr1) consists of two magnetically coupled windings on a ferrite core with polarity dots indicating winding orientation. The coaxial cable connector is shown at the lower left, with the shield connected to ground and the center conductor feeding the transformer. The 200-ohm balanced antenna connects to the two output terminals on the right side of the diagram. This balun provides impedance transformation while feeding a balanced antenna from an unbalanced coaxial cable.

Table showing the recommended number of turns for a 4:1 balun wound on different ferrite toroid cores across three HF frequency ranges. The table includes toroid types T184-2, T200-2, T225-2, T200A-2, T225A-2, and FT240-61, with corresponding turn counts for 1.8–30 MHz, 3.5–30 MHz, and 7–30 MHz operation. Larger iron powder toroids require more turns, while the FT240-61 ferrite core requires the fewest turns due to its higher magnetic permeability.

The Heart of the Antenna: The 4:1 Balun

The balun is critical for the OCF antenna . It has two main jobs:

  1. Impedance Transformation: It converts the ~200-ohm balanced feedpoint impedance of the wire antenna down to ~50 ohms to match your coaxial cable and transceiver.

  2. Common-Mode Choke: It helps prevent RF current from flowing back down the outside of the coaxial cable’s shield. This stops the coax from becoming part of the antenna, which can cause RF in the shack, distorted patterns, and high SWR.

OCF Antenna : Construction Tips

  • Wire: Use insulated copper wire with a diameter of 1.5-2 mm (like AWG 14 or 15). It’s strong and easy to work with.
  • Insulators: Dog-bone type insulators at the ends of each wire are perfect for this project.
  • Tuning: The calculated lengths are a starting point. Your antenna’s resonant frequency will be affected by its height above ground, nearby objects, and the environment. Use an antenna analyzer (like a NanoVNA) to check the SWR on your target bands and trim the wire ends proportionally . A good rule of thumb is to trim 2 inches off the long leg for every 1 inch off the short leg. The best way to tune is to fold back the wire rather than cutting it until you are sure.

The 40-10m OCF dipole is a fantastic antenna for the amateur radio operator who wants multiband performance from a single wire. It is simple to build, low-cost, and, with the correct 4:1 balun, it will provide you with hours of reliable operation across several bands.

Prabakaran is a seasoned author and contributor to leading electronics and communications magazines around the world, having written in publications such as Popular Communications Magazine (USA), ELEKTOR (UK), Monitoring Times (USA), Nuts & Volts (USA), and Electronics For You (India).

Post Comment