Build a 6 Meter Extended Double Zepp With Ladder Line and Coax Choke
Six meters tests your patience. The band sits quiet for days, and then a sporadic E opening rolls in. Your receiver fills with stations hundreds of kilometers away. When this happens, you want an antenna with real gain, not a random piece of wire.
The Extended Double Zepp, usually shortened to EDZ, delivers this gain for little money. You need wire, a few scraps of PVC, some coax, and a free weekend. No rotator. No tower.

The Antenna at a Glance
The drawing shows four parts. A straight wire radiator runs across the top. A short ladder line section hangs from the center. A coax choke sits below, and two plain insulators finish the wire ends.
Each side of the radiator measures 137 inches (3.48 m). A 3 inch (7.6 cm) gap separates the two halves at the center, where the ladder line attaches. Add the numbers and the wire spans about 277 inches, or 7.04 m. One wavelength at 50 MHz is close to 6 m, so this wire runs longer than a full wavelength. A plain half wave dipole is far shorter.
Why the Extra Length Helps
The added length squeezes the radiation pattern. Expect roughly 2 to 3 dB more gain than a dipole, broadside to the wire. Deep nulls appear off the wire ends.
Point the broadside toward the DX you want most. Mount the wire horizontally, because SSB and CW stations on 6 m use horizontal polarization. Matching their polarization keeps your signals strong on both ends.
The Ladder Line Matching Section
Here is the clever part. Feeding a wire this long at the center gives a high impedance, far above 50 ohms. A 30 1/2 inch (77.5 cm) piece of homebrew ladder line brings the impedance down to a friendly level for your coax.
Build the section with the same wire spacing as your main ladder line. Three spacers hold the two wires parallel. Strips of PVC or acrylic work well. Keep the gaps even, because uneven spacing shifts the match.
The Choke Balun
Below the ladder line, the 50 ohm coax makes five turns around a 2 inch PVC pipe. This coil works as a choke. Stray RF stays off the outside of the coax, so the feed line does not join the antenna and distort the pattern.
Sealing the Feed Joint
Look at the spot marked “seal well here” in the drawing. Water loves to creep in where the ladder line meets the coax. Cover the joint with silicone sealant or heat shrink tubing, and be generous. Moisture here will ruin your SWR within one rainy season.
The end insulators are short pieces of 1/2 inch PVC electrical conduit. They cost little, weigh almost nothing, and drill easily. A coat of paint shields the plastic from harsh sun.
Tie thin, strong rope from each insulator to your supports and pull the wire fairly tight. A span of 7 m sags more than most people expect.
Trimming for 50.125 MHz
The lengths in the drawing are final values, measured after trimming for the best match at 50.125 MHz, the familiar SSB calling frequency. Your numbers will differ a little. Wire type, insulation, nearby metal, and height all play a part.
So cut long. Trim both sides in equal, small steps and check the match with an antenna analyzer or a NanoVNA after each cut. Wire you snip off never goes back on, so be stingy.
Here is a nice bonus. Tune the antenna at a comfortable working height, such as a stepladder or a low roof, then raise the wire to its final spot. The SWR changes only slightly. No more climbing up and down a dozen times.
Related Posts
- 40-10m OCF Antenna: A Simple, Multi-Band Wire Antenna
- Building a Compact 40M Magnetic Loop Antenna
- Building the Shorty 4020 Antenna for 40M and 20M Operation
- Building the Ultimate Multiband OCF Dipole for 40m-6m
- Double Dipole Antenna for 80–10 Meter Bands
- Compact Open Sleeve Dipole Antenna for 40 and 20 Meters
Post Comment