Simple 29 MHz AM Transmitter
The 10-meter amateur radio band has always been an interesting playground for homebrew enthusiasts. Its relatively small antenna dimensions, ability to support long-distance contacts during favorable propagation, and suitability for low-power experimentation make it a particularly attractive band for experimenting with simple RF circuits.
The circuit shown here is a compact 29 MHz AM transmitter using a crystal-controlled oscillator and transistor RF stages. It follows the design approach documented by DL4CS in the article “Experiments with amplitude modulation in the 10m band” by DL4CS. The original work describes several home-built 10-meter transmitters, including a three-stage transistor AM transmitter capable of approximately 1 watt of RF output.

The circuit is particularly interesting because it doesn’t depend on exotic RF components. Most of the parts are ordinary resistors, capacitors, RF coils, a 29 MHz crystal and two readily available bipolar transistors.
This circuit and the underlying 10-meter AM transmitter work are credited to DL4CS. The original author’s article should be consulted for the original design context and construction information. This article is an independent explanation of the circuit for educational and amateur-radio purposes.
The transmitter is designed around a crystal-controlled RF oscillator followed by an RF power stage. Audio modulation is applied to the transmitter so that the amplitude of the RF carrier varies with the audio signal.
This is the basic principle of amplitude modulation, or AM. The RF carrier remains at approximately the same frequency while its amplitude changes according to the instantaneous audio waveform.
The original DL4CS design describes a three-stage transistor transmitter for approximately 28–29.7 MHz and notes that the specified component values can produce about 1 watt of output power. The design is based on an older CB-radio transmitter arrangement, which makes it particularly interesting from a historical and homebrew perspective.
The circuit shown here is intended around 29 MHz, with the 29 MHz crystal establishing the operating frequency.
Understanding the circuit
The circuit can be divided into several functional sections: the crystal oscillator, RF amplification/output stage, modulation section, supply filtering, and antenna matching network.
At the left side of the circuit is the crystal oscillator. A 29 MHz quartz crystal provides the frequency reference. Crystal control is useful in a simple transmitter because it provides considerably better frequency stability than relying entirely on a free-running LC oscillator.
The oscillator uses a BD136 PNP transistor. The use of a PNP transistor in the oscillator stage is consistent with the design approach described by DL4CS. The RF signal generated here is subsequently coupled into the following transistor stage.
The second major transistor is the BD135 NPN transistor, which provides RF power amplification. The output network surrounding this transistor contains RF coils and capacitors that are tuned to the operating frequency.
The collector circuit is especially important. At 29 MHz, wiring, component leads and layout are no longer insignificant. A circuit that works perfectly on a breadboard at audio frequency can behave very differently at VHF-borderline frequencies. For this reason, the physical construction of the RF section matters almost as much as the schematic.
Crystal-controlled operation
The 29 MHz crystal is the heart of the frequency-generating section. A crystal oscillator is preferred here because the resonant frequency of quartz is much more stable than that of a simple LC oscillator. The crystal effectively establishes the carrier frequency, while the surrounding capacitors, coil and transistor determine the conditions under which oscillation occurs.
For a homebrew AM transmitter, this approach has another advantage: the operator doesn’t have to continually correct the carrier frequency while transmitting.
The original DL4CS article discusses several methods of generating and controlling frequencies in the 10-meter band, including crystal-controlled transmitters and super-VFO arrangements.
The BD136 oscillator transistor
The BD136 is a PNP power transistor used here as the RF oscillator device. It should not be treated like a small-signal transistor merely because the oscillator power is relatively modest. At 29 MHz, the transistor’s RF characteristics and the physical circuit layout become important.
The oscillator section contains the 29 MHz crystal together with the associated RF components. The 110 pF variable capacitor provides adjustment of the oscillator/resonant circuit. The adjacent fixed capacitors provide RF feedback, bypassing and frequency-selective functions.
When constructing the circuit, keep the crystal and its associated components physically close to the transistor. Long wires can introduce unwanted inductance and stray capacitance.
The BD135 RF power stage
The BD135 NPN transistor is used for the RF power stage. The transistor receives the RF drive from the oscillator section and develops a higher RF signal suitable for feeding the output matching network. The collector circuit contains the RF coil and capacitors required to transform the transistor’s output into a useful 29 MHz signal.
The original DL4CS description identifies this family of transistor transmitters as capable of approximately 1 watt of output power with the specified component values. It also notes that the circuit can be modified for higher carrier power, although doing so changes the requirements of the modulation system and output stage.
For a first build, it’s better to reproduce the original low-power arrangement rather than immediately trying to increase the output.
AM modulation
The point marked “Modulation” on the schematic is where the audio signal is introduced. Amplitude modulation requires the RF carrier amplitude to follow the audio waveform. In a simple transistor transmitter, this can be accomplished by varying the operating conditions of the RF power stage.
The original DL4CS design discusses emitter modulation in its smaller two-stage transmitter. In that arrangement, audio is coupled into the emitter of the RF power transistor, changing the current conduction angle of the class-C output stage and producing usable AM.
The three-stage design shown in the supplied schematic uses the modulation input around the transistor circuitry so that the RF amplitude changes with the applied audio.
This is one of the appealing aspects of the circuit: a relatively modest audio amplifier can be used to produce intelligible AM without requiring a complicated balanced modulator or SSB-generation system.
However, modulation level needs to be controlled carefully. Excessive audio drive can produce overmodulation, resulting in distorted audio and excessive unwanted sidebands.
The 12-volt supply
The circuit is designed around a +12 V DC supply. The 10 Ω resistor near the supply input and the bypass capacitors provide supply isolation and RF decoupling. This is important because RF energy can easily travel back through the power supply wiring and cause instability or unwanted radiation.
The supply wiring should be short, with good grounding between the RF stages and the supply bypass capacitors.
A regulated 12 V supply is preferable for initial testing. A stable supply also makes troubleshooting easier because changes in RF output won’t be confused with changes caused by supply-voltage variation.
The output network
The output section contains a variable capacitor, fixed capacitors and an RF coil leading to the antenna connection. This isn’t simply an impedance-matching arrangement. The network also performs an important filtering function.
RF power amplifiers generate harmonics. A transistor operating at 29 MHz can potentially produce significant energy at 58 MHz, 87 MHz and other harmonic frequencies. The output network is therefore required to provide the appropriate impedance transformation while reducing unwanted harmonic energy.
The original DL4CS transmitter designs use a two-stage Pi low-pass filter for this purpose in the smaller transmitter. The author specifically notes that this substantially reduces harmonic radiation.
Recommended inductors
| Circuit position | Recommended value | Practical range | Suggested construction |
|---|---|---|---|
| 101 µH coil at +12 V | 101 µH RFC | 82–150 µH | RF choke, preferably axial/radial RFC |
| Oscillator/tank coil | 0.30–0.40 µH | 0.25–0.50 µH | Air-core |
| Driver/PA collector coil | 0.25–0.35 µH | 0.20–0.45 µH | Air-core |
| Output/tuning coil | 0.20–0.30 µH | 0.15–0.35 µH | Air-core |
| Antenna coupling coil, if used separately | 0.10–0.20 µH | 0.08–0.25 µH | Air-core |
The 101 µH component is different from the other coils. It acts primarily as an RF choke and should not be treated as part of a 29 MHz resonant tank.
Practical air-core construction
For approximately 0.25–0.4 µH, a useful starting point is:
- former: 6–8 mm diameter
- wire: 0.6–1.0 mm enamelled copper
- turns: roughly 3–5 turns
- winding: single layer
- keep leads extremely short
The exact number of turns needs to be adjusted experimentally. Don’t assume that five turns on an 8 mm former will produce exactly 0.33 µH; coil spacing and geometry make a noticeable difference at 29 MHz.
A small adjustable spread between turns is actually useful because you can slightly change the inductance during alignment.
The coil immediately associated with the 110 pF variable capacitor should be treated as the main output-tank coil.
I’d start around 0.22–0.27 µH. The 110 pF capacitor and approximately 0.27 µH coil resonate close to 29 MHz:
29 MHz + 110 pF + 0.27 µH → approximately 29.4 MHz
That’s close enough to provide a useful tuning starting point, particularly because the actual circuit has transistor and stray capacitances.
For the 150 pF and 270 pF capacitors in the antenna/filter section, the effective capacitance is more complicated because they are part of the matching/filter network rather than simply one capacitor across one coil.
The original DL4CS three-stage transmitter uses coils salvaged from an older CB transmitter with a similar circuit. The original documentation does not specify a separate inductance value for every coil. For a modern reproduction, approximately 0.2–0.4 µH air-core coils are reasonable starting points for the 29 MHz resonant sections, with final adjustment performed using the variable capacitors and RF measurements.
Related Circuits
- Build a 4-Pin Crystal Oscillator AM Transmitter
- DIY 1 MHz AM Transmitter: A Perfect Weekend Project for Beginners
- DIY IRF510 AM Transmitter Circuit
- Build Your Own Commando AM Transmitter
- Build Your Own 40M AM Transmitter: A Classic Radio Project
- Build Your Own Grenade AM Transmitter Circuit: A Complete Guide
Post Comment